Nokia 5.1

Nokia5.1


Supported operations


Drivers


Connection

  • All drivers should be installed before connection.
  • You dont need to perform connect and disconnect operation every time you make an operation with handset. Connection should be done once before doing any operations with handset. After all operations with hansdset are complete, disconnect.
  • The phone battery should be charged on 40 percent or more before performing any operation on it! In case battery uncharges during work process, the phone wont switch on and charge battery. In this case you will have to take out the battery from the phone and charge it with external charger.
  • Use usb ports placed on the backside of PC to connect to the phone
  • Do not connect or disconnect other USB cables into the PC during performing operation with the phone
  • Dont use USB HUBs, long or very thin USB cables.
  • In case 'Read flash failed' or 'Write flash failed' error appears in the log, try to change the PC or reinstall drivers

Connection Cable: micro usb

To connect to the handset do the following steps:

  1. Go to 'direct services' Tab
  2. Choose your handset model in the combobox at the upper left side of the window
  3. Disconnect the handset from the cable.
  4. Remove battery from the handset.
  5. Push Connect button in the application form
  6. Insert battery and connect cable to the phone. The battery should be charged
  7. You should see the 'Phone found. Sending loader' strings in the Log
  8. If the handset began to load(you see the 'Nokia' logo), the connection with handset failed! Click on 'Cancel', disconnect the pnone, switch it on, than switch it off and repeat 'Connection' procedure once more. If it doesnt help, try relaunching EasyBox Mtk application, install drivers or charge phones battery.

To disconnect the handset do the following steps:

  1. Click on 'Disconnect' button
  2. Disconnect the cable from the handset.
Never unplug cable until ongoing operations are finished. This can lead to bricking your phone.


Get Info

If you need to print the information about connected phone once more, you can click on Get Info button. This operation is read only and doesnt change anything inside of the phone.
The following information is printed:
  • Imei numbers
  • SKUID
  • Simlock information
  • Frp information
  • Firmware version
  • Android version
  • Firmware compilation date time


Unlock

Before changing any data in the handset flash memory, EasyBox Mtk dumps all security partitions into the file in the 'backups' folder. You always can restore lock data by flashing the security backup file back to the handset.

To unlock the handset do the following steps:

  1. Connect to the phone
  2. Click on the Unlock button
  3. Wait until 'Phone successfully unlocked' appears in the log
  4. Disconnect the phone


Flash firmware

Now EasyBox Mtk doesnt support flashing from scatter file for Nokia phones, because sometimes it leads to bricking your phone. If you have scatter file and you are sure it is ok, please send it to our technical support. We will chek this file and make an sbf from it
  • Flash firmware process erases FRP and USERDATA partitions. All user data will be lost. Please save all important data from the phones internal memory to safe place before doing flash firmware.
  • You can flash firmware for different providers but dont forget to change SKUID as well.

To flash firmware on the handset do the following steps:

  1. Download firmware from download area
  2. Connect to the phone
  3. Click on the ... button under the Flash tag
  4. Select *.sbf file in the firmware folder
  5. Click on the Firmware button in the 'Flash' section
  6. Wait untill firmware download process finishes
  7. Disconnect the phone
  8. Switch on the phone and wait until it bootes. The boot process after firmware download can last up to 10 minutes. Please be patient


Repair Imei

If you need to restore the original imei, you need to flash NVM backup file , which was made before changing imei. Nvm backup file is automatically made before imei change operation. All backup files are stored in 'Backups' folder.
You can check imei numbers by typing *#06# in the dialing window of the handset.

To change imei numbers do the following steps

  1. Connect to the phone
  2. Change imei number to the value you want at the right bottom side of the window
  3. Press Repair IMEI button
  4. Wait until 'IMEI successfully repaired' appears in the log
  5. Disconnect the phone
  6. Switch on the handset and check new imei numbers.


Factory Reset

To make factory reset do the following steps

  1. Connect to the phone
  2. Press Factory reset button
  3. Disconnect the phone
  4. Switch on the handest and wait until initializing process is finished


Reset FRP

To reset FRP do the following steps
  1. Connect to the phone
  2. Press Reset frp button
  3. Wait until 'FRP Resetting complete' appears in the log
  4. Disconnect the phone


Dump security

Dump security operation is helpful when you want to backup security data before unlocking the phone

To dump security area do the following steps
  1. Connect to the phone
  2. Press Security button in the dump sestion and select the name for the file to save
  3. Wait until 'Dump security success' appears in the log
  4. Disconnect the phone


Flash security

Flash security operation can be helpful when you want to restore simlock of the unlocked handset

To flash security area do the following steps

  1. Connect to the phone
  2. Click on the ... button under the Flash tag
  3. Select *.sbf file with security backup
  4. Press Security button in the 'Flash' section
  5. Wait until 'Flashing security success' appears in the log
  6. Disconnect the phone


Dump NVM

Dumping NVM is helpful if you are aware that some action can damage the phone NVM area. In this case you will be able to restore NVM from backup file.
'Dump NVM' operation automatically executed before flashing firmware or repairing imei operation. The nvm backup file is saved in the 'Backups' folder.

To dump NVM do the following steps

  1. Connect to the phone
  2. Press NVM button in "Dump" section, and select the name for the file to save
  3. Wait until 'Dump NVM success' appears in the log
  4. Disconnect the phone


Flash NVM

Flashing Nvm will restore NVM area from the NVM backup file.
Flashing nvm will restore imei numbers to the values wich were saved in the nvm file.

To flash NVM do the following steps

  1. Connect to the phone
  2. Click on the ... button under the Flash tag
  3. Select *.sbf file with nvm backup
  4. Press NVM button in the 'Flash' section
  5. Wait until 'Flashing NVM success' appears in the log
  6. Disconnect the phone


Repair SKUID

You can always restore original SKUID by flashing product info backup file, which automatically created in 'Backups' folder.
Repair SKUID can be helpful when you want to reflash your phone with the new firmware version.

To change SKUID do the following steps

  1. Connect to the phone
  2. Change SKUID number in the edit field left to Repair SKUID button and then click on this button
  3. Wait until 'SKUID repair success' appears in the log
  4. Disconnect the phone


Flash product info

Product info dumps are automatically created in 'Backups' folder before any operation, which changes Product Info partition.

You can flash product info back to restore original SKUID

To flash product info do the following steps

  1. Connect to the phone
  2. Click on the ... button under the Flash tag
  3. Select *.sbf file with product info backup
  4. Press "Product info" button in the 'Flash' section
  5. Wait until 'Flashing product info success' appears in the log
  6. Disconnect the phone