Admin

Nokia 222 RM1137

RM1137


Supported operations


Drivers


Flash Care Firmware

Care Firmware contains 5 firmware partitions and can be flashed in every phone, even if the phone is efused.
  • EasyBox Mtk doesnt support flashing firmware of the version lower, than the phone currently has.
  • You should flash the firmware of the product code, your handset has. You can find it at the back of the phone under the battery. Some firmware files dont have product code. Flash them on your own risk.
  • Before this operation starts, EasyBox Mtk will suggest you to make a backup dump. We strongly advice you to make a backup dump on every flash operation. Backup files are stored in 'Backups' folder, which is located in application folder.
  • It is highly recommended to make dump full first before any flashing. In case new firmware causes trouble, you can reflash firmware from full dump file.
  • Use only the firmware for the RM1137. Flashing firmware for other models, even if these models have the same market name, will brick the phone!

To flash care firmware on the handset do the following steps:

  1. Disconnect the handset from the cable if it is connected
  2. Click on the ... button under the Flash tag
  3. Select *.sbf file in the firmware folder
  4. Click on the Care Firmware button in the 'Flash' section
  5. Connect handset to the cable
  6. Wait until firmware download process finishes
  7. Disconnect the phone
  8. Switch on the phone and wait until it bootes. The boot process after firmware download can last up to 10 minutes. Please be patient

Flash Care Firmware From Dump

  • EasyBox Mtk doesnt support flashing firmware of the version lower, than the phone currently has.
  • You should flash the firmware of the product code, your handset has. You can find it at the back of the phone under the battery. Some firmware files dont have product code. Flash them on your own risk.
  • Before this operation starts, EasyBox Mtk will suggest you to make a backup dump. We strongly advice you to make a backup dump on every flash operation. Backup files are stored in 'Backups' folder, which is located in application folder.
Use only the firmware for the RM1137. Flashing firmware for other models, even if these models have the same market name, will brick the phone!

To flash care firmware on the handset do the following steps:

  1. Disconnect the handset from the cable if it is connected
  2. Click on the ... button under the Flash tag
  3. Select *.sbf file which was created during DumpFull operation
  4. Click on the Care Firmware button in the 'Flash' section
  5. Connect handset to the cable
  6. Wait until firmware download process finishes
  7. Disconnect the phone
  8. Switch on the phone and wait until it bootes. The boot process after firmware download can last up to 10 minutes. Please be patient

Flash Factory Firmware

Care firmware contains only 5 firmware partitions and can be flashed in all handsets. Factory firmware contains 5 firmware partitions + 3 bootloader partitions but can be flashed only in not efused handsets. Factory firmware is much safer and can even revive bricked handsets. If you have handset, which is not efused, you should use factory firmware.
  • EasyBox Mtk doesnt support flashing firmware of the version lower, than the phone currently has.
  • You should flash the firmware of the product code, your handset has. You can find it at the back of the phone under the battery. Some firmware files dont have product code. Flash them on your own risk.
  • Factory firmware is supported only for not efused handsets. To check if the phone is efused, make 'GetInfo' opeation. If the phone is efused there will be a notice in the log, that this phone cant be flashed with factory firmware.
  • Before this operation starts, EasyBox Mtk will suggest you to make a backup dump. We strongly advice you to make a backup dump on every flash operation. Backup files are stored in 'Backups' folder, which is located in application folder.
  • It is highly recommended to make dump full first before any flashing. In case new firmware causes trouble, you can reflash firmware from full dump file.
  • Use only the firmware for the RM1137. Flashing firmware for other models, even if these models have the same market name, will brick the phone!

To flash factory firmware on the handset do the following steps:

  1. Disconnect the handset from the cable if it is connected
  2. Click on the ... button under the Flash tag
  3. Select *.sbf factory firmware file which was loaded from the download area
  4. Click on the Factory Firmware button in the 'Flash' section
  5. Connect handset to the cable
  6. Wait until firmware download process finishes
  7. Disconnect the phone
  8. Switch on the phone and wait until it bootes. The boot process after firmware download can last up to 10 minutes. Please be patient.

Flash FAT

With the help of this feature you can restore file system of the phone from the full dump file. This will restore phone book, security code etc.
Before this operation starts, EasyBox Mtk will suggest you to make a backup dump. We strongly advice you to make a backup dump on every flash operation. Backup files are stored in 'Backups' folder, which is located in application folder.

To flash FAT on the handset do the following steps:

  1. Disconnect the handset from the cable if it is connected
  2. Click on the ... button under the Flash tag
  3. Select *.sbf full dump file which was dumped earlier.
  4. Click on the Flash FAT button in the 'Flash' section
  5. Connect handset to the cable
  6. Wait until flash process finishes
  7. Disconnect the phone
  8. Switch on the phone and wait until it bootes.

Flash Secure Data Storage

Secure Data Storage(SDS) is a special partition which holds all immutable nvm data, like calibration data etc. If this partition is corrupted or changed the phone will go in 'Contact service' mode. Now you can restore this partition from full dump file or from the sds backup file.
  • Before this operation starts, EasyBox Mtk will suggest you to make a backup dump. We strongly advice you to make a backup dump on every flash operation. Backup files are stored in 'Backups' folder, which is located in application folder.
  • EasyBox Mtk will dump current sds parition and save it in the 'Backups' folder. If something goes wrong you can flash sds data from this backup file. The name of the file will contain product code and imei. So you always can find the file, using it.
Be careful. If you flash this partition from another phone, your phone will go in 'Contact service' mode!!!

To flash Secure Data Storage on the handset do the following steps:

  1. Disconnect the handset from the cable if it is connected
  2. Click on the ... button under the Flash tag
  3. Select *.sbf full dump file which was dumped earlier.
  4. Click on the Flash SDS button in the 'Flash' section
  5. Connect handset to the cable
  6. Wait until flash process finishes
  7. Disconnect the phone
  8. Switch on the phone and wait until it bootes.

Dump Full

To make dump full file do the following steps:

  1. Disconnect the handset from the cable if it is connected
  2. Click on the DumpFull button under the Dump tag
  3. Select the file path to save the file which will be created
  4. Connect handset to the cable
  5. Wait until dump full process finishes
  6. Disconnect the phone
  7. Switch on the phone and wait until it bootes.

Format FAT

Before this operation starts, EasyBox Mtk will suggest you to make a backup dump. We strongly advice you to make a backup dump on every flash operation. Backup files are stored in 'Backups' folder, which is located in application folder.
Be careful. 'Format FAT' operation erases all user data, including phone book, security codes etc.

To format FAT in the phone do the following steps:

  1. Disconnect the handset from the cable if it is connected
  2. Click on the Format FAT button under the Services tag
  3. Connect handset to the cable
  4. Wait until format fat process finishes
  5. Disconnect the phone
  6. Switch on the phone and wait until it bootes.

Get Info

Get info operation is useful when you need information whether or not the phone is efused(restricts factory firmware), what is firmware version, nor flash type and size etc.
Get Info operation reads the following data:
  • Chipset
  • Hardware subcode
  • Security level. Does this phone allows to flash factory firmware
  • Product Code
  • Imeis
  • Chip Name
  • Nor flash chip name
  • Nor flash size

To perform Get Info operation do the following steps:

  1. Disconnect the handset from the cable if it is connected
  2. Click on the Get Info button under the Services tag
  3. Connect handset to the cable
  4. Wait until get info process finishes
  5. Disconnect the phone
  6. Switch on the phone and wait until it bootes.